Mercedes-Benz ML | Perform basic programming after disconnecting battery (W164)
1,4,Basic programming on model W 164||| 5,10,First connect the battery so that the vehicle|is supplied with power again.|| 11,15,When tightening the screws,|use a torque of 6 Nm.|| 16,20,The next steps are performed|from the driver seat.|| 21,24,All of the doors must be closed.||| 25,28,Now switch on the ignition and|the actual programming can start.|| 29,32,First switch the low beams|on and back off.|| 33,39,Then activate the air conditioning by pressing|the "Off" button on the center console.|| 40,46,Give the unit a good run.|Then switch it back off.|| 47,50,You now have to listen to some music.||| 51,55,Depending on the equipment installed,|switch the radio or COMAND on and back off.|| 56,60,This takes a few moments. |The units need a bit of time to start up.|| 61,69,Now open the electric power sliding roof|and close it again.|| 70,74,After it closes, keep the switch pressed|for at least three seconds.|| 75,78,Use the express function|to immediately check ...|| 78,82,... whether normalization of the sliding roof|was successful.|| 83,89,If the roof opens all the way, everything is OK.|If not, the procedure must be repeated.|| 90,94,To program the anti-pinch protection,|lower the windows all the way down ...|| 94,97,... and then all the way back up.||| 98,102,In this position, again keep the switch pressed|for at least three seconds.|| 103,107,To test the window, simply press the switch|past the actuation point.|| 108,111,Repeat these steps for all of the windows.||| 112,115,To normalize the steering angle sensors,|the engine first has to be started.|| 116,125,Then turn the steering wheel all the way |to the left and then all the way to the right.|| 126,129,The next programming steps are performed|outside of the vehicle.|| 130,137,Switch off the engine, remove the ignition key,|get out and close the driver door.|| 138,141,The ignition key is needed to program|the automatic self-locking.|| 142,146,Simply lock the driver door|and then unlock it again.|| 147,151,Then open the driver door|and close it again - finished!|| 152,157,Now you need to take the vehicle outside|to adjust the clock on the instrument cluster ...|| 157,161,... because the integrated GPS receiver|needs a good connection to the satellites.|| 162,165,Reception is better outside, so just|drive the vehicle out of the workshop.|| 166,170,Next, press the service button on the |COMAND and then the "Time" button.|| 171,174,Set the current time|using the arrow buttons.|| 175,179,Confirm with "OK" and the vehicle|is right up-to-date again.|| 180,183,Now calibrate the compass, if installed.||| 184,189,For further information, see WIS document|AR00.19-P-0200GZ.|| 190,193,Basic programming of the ML|is now complete.|| 194,197,You can hand the key back to the customer|with confidence.||
1,4,Basic programming on model W 164||| 5,10,First connect the battery so that the vehicle|is supplied with power again.|| 11,15,When tightening the screws,|use a torque of 6 Nm.|| 16,20,The next steps are performed|from the driver seat.|| 21,24,All of the doors must be closed.||| 25,28,Now switch on the ignition and|the actual programming can start.|| 29,32,First switch the low beams|on and back off.|| 33,39,Then activate the air conditioning by pressing|the "Off" button on the center console.|| 40,46,Give the unit a good run.|Then switch it back off.|| 47,50,You now have to listen to some music.||| 51,55,Depending on the equipment installed,|switch the radio or COMAND on and back off.|| 56,60,This takes a few moments. |The units need a bit of time to start up.|| 61,69,Now open the electric power sliding roof|and close it again.|| 70,74,After it closes, keep the switch pressed|for at least three seconds.|| 75,78,Use the express function|to immediately check ...|| 78,82,... whether normalization of the sliding roof|was successful.|| 83,89,If the roof opens all the way, everything is OK.|If not, the procedure must be repeated.|| 90,94,To program the anti-pinch protection,|lower the windows all the way down ...|| 94,97,... and then all the way back up.||| 98,102,In this position, again keep the switch pressed|for at least three seconds.|| 103,107,To test the window, simply press the switch|past the actuation point.|| 108,111,Repeat these steps for all of the windows.||| 112,115,To normalize the steering angle sensors,|the engine first has to be started.|| 116,125,Then turn the steering wheel all the way |to the left and then all the way to the right.|| 126,129,The next programming steps are performed|outside of the vehicle.|| 130,137,Switch off the engine, remove the ignition key,|get out and close the driver door.|| 138,141,The ignition key is needed to program|the automatic self-locking.|| 142,146,Simply lock the driver door|and then unlock it again.|| 147,151,Then open the driver door|and close it again - finished!|| 152,157,Now you need to take the vehicle outside|to adjust the clock on the instrument cluster ...|| 157,161,... because the integrated GPS receiver|needs a good connection to the satellites.|| 162,165,Reception is better outside, so just|drive the vehicle out of the workshop.|| 166,170,Next, press the service button on the |COMAND and then the "Time" button.|| 171,174,Set the current time|using the arrow buttons.|| 175,179,Confirm with "OK" and the vehicle|is right up-to-date again.|| 180,183,Now calibrate the compass, if installed.||| 184,189,For further information, see WIS document|AR00.19-P-0200GZ.|| 190,193,Basic programming of the ML|is now complete.|| 194,197,You can hand the key back to the customer|with confidence.||